|
Introduction
|
Natural Gas Test Results Canada
|
Natural Gas Flier
|
Installation Guides
|
Testimonials
|
How does it work?
How does magnetism affect Hydrocarbon-based combustible fluids such as gasoline, diesel fuel, kerosene, LP and natural gas?
To promote complete combustion, Oxygen must be combined with the Hydrocarbon molecule. Because the net charges of the Hydrocarbon and Oxygen molecules are both negative, there are repulsive forces, not attractive forces present. To overcome this repulsion, combustion engineers design combustion processes so that the combustion envelope is super-saturated with Oxygen. The overwhelming Oxygen concentration forces the two similarly charged molecules to be in close physical proximity to each other and eventually, combine to create the combustion climate. In essence the fuel uses the available Oxygen.
Since Fuel, like most fluids, can be ionized by an external magnetic force, it will exhibit many of the same physical-atomic characteristics as water.
 When MAGNETIZED, the fuel’s Hydrocarbons are ionized to exhibit a net positive charge (as with water). The change in charge allows the fuel to aggressively attract and bond with available (negatively charged Oxygen. This creates a more comprehensive Hydrocarbon molecule with its own Oxygen supply. The end result is a more efficient and fully burning, explosive mixture which now has its own oxygen base.
Magnetizing the fuel also polarized the mixture by replacing the normally chaotic fluid with an even, positively charged uniformly aligned fuel, which, with the oxygen bonding, results in an almost total burn for complete BTU output (no hot spotting) and better fuel efficiency. The magnetized fuel also attracts and removes previous carbon and varnish build-up (similar to the scale removal action in an aqueous environment) in the jets, injectors and engine for even higher efficiency. Cleaning to Factory – New Specs, thereby running a cleaner, more efficient engine, which of course lasts longer with improved performance.
What Can a Magnet Technology Do for Diesel Powered Vehicles?
In addition to increasing fuel efficiently, when properly magnetized, diesel fuel will resist gelling. (Gelling is a temperature induced “crystallization” that can be considered somewhat analogous to the scaling mechanism in an aqueous solution). This means that during cold weather, special fuel additives may be eliminated. Also, for the same oxygen bonding and cleaning reasons as outlined above, immediately apparent is the increase in available power and the marked reduction in the exhaust smoking normally associated with diesel power.
After Installation, what type of behavior can be expected from a newly MAGNETIZED car?
Immediately evident will be an increase in the power/mpg. This is the newly energized fuel exploding in the combustion chambers. Depending upon the carbon & varnish condition of the system, the extra mpg may be reduced temporarily. This is a result of the MAGNETIZED fuel’s cleaning capability, dissolving the carbon and the varnish build-up from within the system. It occurs when tiny particulates may briefly impede the fuel flow. The particulate will dissolve. The power will then return, signifying the completion of the “cleaning” stage. At this point, the jets, lines, and injectors return to peak efficiency. |
|
Introduction
|
Natural Gas Test Results Canada
|
Natural Gas Flier
|
Installation Guides
|
Testimonials
|
|
1.9 MB PDF file - click/right click on link above |
Download Fuel Flier
- click here |
|
|
Introduction
|
Natural Gas Test Results Canada
|
Natural Gas Flier
|
Installation Guides
|
Testimonials
|
Installation Guide for
GMX MAGNETIC FLUID FUEL DEVICES |
| Small vehicles |
1 GMX Model 400 |
| Midsize vehicles |
2 GMX Model 400s |
| SUVs |
2 GMX Model 400s |
| Pickups |
2 GMX Model 400s |
| Motor Homes |
2 GMX Model 400s |
| Buses |
2 GMX Model 400s |
| Commercial Vehicles |
2 GMX Model 400s |
| Semi-Trucks |
1 GMX Model 800 and
1 GMX Model 400 |
Natural Gas Installations
|
GMX Corporate recommends the following
for natural gas line GMX applications:
- Main line to home. Between the meter and the hook up, if there is a flex, plex, stainless steel, or copper, use at least
2 GMX units. 3 is even better as the longer the magnetic
field, the better the savings.
- Treat each application as well if there is flex line to the appliance--gas furnace, hot water heater, range, dryer, gas fireplace, etc. GMX recommends 2 units on each application.
- Sizing:
1/4-1/2" flex line |
use 2 Model 400s per line |
5/8-1" flex line |
use 2 Model 800s per line |
1-1 3/4" flex line |
use 2 Model 848s per line |
2" line |
use 2 Model 8000s per line |
3/4" line |
use 4 Model 8000s |
5-6" line |
use 6 Model 8000s |
7-8" line |
use 8 Model 8000s |
9-10" line |
use 10 Model 8000s |
- Lines that are made of iron can be swapped out for stainless steel for where the application of GMX Units are to be placed.
|
Installation Instructions for
GMX MAGNETIC FLUID FUEL DEVICES
On small vehicles, use 1 GMX Model 400. Place the unit at least
8-12 inches upstream from the area to be treated.
Place it 8-12
inches after any pump, filter, or other turbulance
causing
device. The direction of flow of the fluid
being treated does not
make any difference.
Place the unit 6-12 inches away from any
high heat sources, for
example, the manifold and exhaust system.
Place it 12 inches away
from the diagnostic control centers and sensors.
The unit should
be mounted on the fuel line after the filter,
before the
carburator. On fuel injected engines, mount
the unit on the line
to the engine, not the return line.
On midsize vehicles, sport utility vehicles,
pickups, diesel
pickups, buses, motor homes--follow the
above directions, but
install 2 GMX Model 400s instead of one.
Place the units in tandem.
For semi trucks--install 1 GMX Model 800
and 1 GMX Model 400.
Place the GMX Model 800 on the main fuel
line between the fuel
tank and the engine's fuel transfer pump.
Place the GMX Model 400
between the fuel transfer pump and the
fuel injection pump manifold. |
So far, we are finding a minimum savings of 20% having GMX units on
natural gas lines.
For natural gas line installations:
-
If the main line has black iron, you cannot install the units on it.
If the connection between the meter and hook up is flex line,
then install 2 Model 800s on it.
-
If you cannot install it on the main line because there is no
flex line, then install the units on the flex line for each
application.
-
If the flex line, example on a gas furnace, is 3/4-1", then
install 2 Model 800s.
-
If the flex line is 1/2", example on some hot water heaters,
then install 2 Model 400s.
-
Some homes may need 2 Model 800s and 4 Model 400s,
depending on what they heat with gas.
-
For commercial applications, use the sizing chart to determine
what is needed. For example, if the main line is 3" and is of
stainless steel or flex, then install 4 Model 8000s.
|
|
|
Installation on Natural Gas water heater |
Installation on Natural Gas furnace |
|
Natural Gas Installation on Home |
|
Introduction
|
Natural Gas Test Results Canada
|
Natural Gas Flier
|
Installation Guides
|
Testimonials
|
|
Made in the USA
